Spidertrax Wheel Spacers (1.25″) – Wider Stance
If you are looking to push your wheels out a bit further and widen your stance, the Spidertrax Wheel Spacers are a good option. There is a reason why these spacers are the go-to option. Spidertrax spacers are a quality-made product backed by a customer-first company.
Find it online
- Spiertrax WHS-007 Hub Centric Check Price
- Read the installation here
They come in pairs of 2 (one box) and you need 4 (two boxes).
Table Of Contents
Overview
Spacers with -6 Offset Fuel Wheels
Whether you are going to install a leveling kit or a suspension system, spacers are something you should consider if you want a wider stance. After a lift, you start to push your lower control arms down, which pulls your wheels/ tires inside the well. With spacers or a larger negative offset, you can push your wheels back out to widen the stance.
It is also important to note that spacers increase rubbing in your wheel well. Do your research before committing to a purchase. Depending on the tire size you are running, and the specs on your wheel will depend on the amount of rubbing if any you will have after installing spacers.
In most cases, your tires will rub on the firewall and body mounts after installing spacers. Common trimming and cutting are usually required after spacers or large negative offset wheels.
Wider Tires Vs. Skinny Tires
With a wider tire, your rubbing is going to be more severe than a skinny tire. 295/70R17s are going to cause more rubbing than 285/70R17s because they are 0.55″ wider. Also, 33/12.5/17s are .9″ wider than the 295/70s, so these are very wide compared to the 285/70s. Wider means more contact and more rubbing. Skinny tires like a 285/75R17 are still going to rub but in most cases, it will be less than a 295/70.
Factors like make, model, suspension, coils, and UCAs also come into play. You can use the tire calculator to check tire size and then use your best judgment on the size you want to run vs. the amount of trimming you are willing to do.
How does this affect wheel spacers and rubbing?
The wider your wheel, the more rubbing you will have. Once you add another 1.25″ to the face of your hub, you are pushing your entire wheel and tire further outside of the well. This will usually make contact with parts of your fenders sooner.
Again, this all depends on the size wheel and tire you have mounted. If you like the wider-looking stance, you will make it work.
Hubcentric Spacers
These spacers are hub-centric. The size is 1.25″ and they have been designed for our exact bolt pattern. After installation, you should have an additional 1.25″ of space between your brake rotors and wheel.
Alignment? You don’t need to get an alignment after installing. To each their own though. If you feel like it, go for it.
Reasons You Need Spacers
- Stance/Appearance: This may be one of the most popular reasons why people add pacers. By installing a set of these, it will push your wheels out of your wheel well to give your 4Runner a much more aggressive stance. This all comes down to personal preference. Some people like the “poke” look and some don’t.
- Space/Clearance: By getting new aftermarket brake calipers, you may have to push your wheel away from the brake caliper. This all depends on what brand of brakes you get. Some require spacers but most do not.
- Offset/Correction: If you’ve installed a suspension lift on your 4Runner, you might need wheel spacers to correct your stance. When you lift your vehicle, the wheels are pulled closer to the wheel wells. This happens because the suspension geometry changes: your Upper Control Arm (UCA) and Lower Control Arm (LCA) tilt more downward rather than outward, which shifts your wheels and tires inward. Wheel spacers can help by pushing the wheels and tires back out away from the wheel wells. However, the need for spacers depends on your specific setup. In many cases, using spacers might lead to increased rubbing against the wheel wells compared to before, so it’s important to carefully consider whether spacers are the right solution for your lift and wheel configuration.
- Rubbing: Some people might think that installing a set of spacers will help prevent rubbing. That is not necessarily the case. When you push your wheels/tires out more, you’re changing the scrub radius which puts your tire closer to the firewall.
Hub-Centric and Offset
If you are going to buy a set, make sure they are hub-centric to your vehicle, and yes, this brand is hub-centric. Hub-centric means that the load you are putting on your wheels is not on the studs, and your wheel stays perfectly center.
Buying a set of wheel spacers is similar to buying a set of wheels with a negative offset. The negative offset on a wheel determines how far the wheel sticks out from the hub.
I’ve had my 1.25” spacers on since I purchased my 4Runner solely to make it look somewhat decent. Even with the all weather Dunlop’s it came with, it looked good. It was only when I got AT tires at 265/70/17 it added some aggressiveness look to it. Then, I got 275/70/17s, and it looks amazing.
The OEM studs on 5th gens for the front wheels do not expose as many threads as the rear wheels, and the lug nuts that are provided with these kits do not allow enough rotations (at least 8 complete rotations). I recommend purchasing: Amazon.com: 24pcs Chrome Silver Open ET Lug Nuts – Metric 12×1.5 Thread Size – 1 inch Length – Extended Threads – Cone Conical Taper Seat Shank – Compatible with Select 6Lug Vehicles and Aftermarket Wheels : Automotive
Update: I commented above using Mammoth spacers. After the post, I swapped them for Spidertrax, and found they were not needed. Just make sure the set of spacers you buy don’t need the extended thread lug nuts.
I just bought a 2023 TRD Off Road. No lifts or mods(Not planning on it). Just the stock wheels and tires. Would there be any rubbing or adjustment needed in this case? Just looking for the wider stance and nothing more.
Thanks in advance!
Ben
Hello. I have a 2021 T4R with 275/55 R20 with 0 offset, and I’m having issues with some major rubbing on the inside of the front tires. I figured this was the best place to ask, but I’m considering spaces to push out the wheel amd tires out from the UCAs because that is the area that I feel is rubbing. Would spaces help this or is this something where I need to purchase a leveling kit as well? Please advise, any comments and help is welcome. Thanks.
Hi,
I am interested in giving my 2020 4Runner SR5 a more aggressive appearance. I am currently running Bridgestone 265/70R17 on the factory TRD rims. I do not have a lift. I would like to know which Spidertrax (1.25 or 1.50) would be best, without creating any rubbing.
Thank you in advance,
Carlos
I have a 2018 5th 4r with stage 2 icon lift set at 3 1/4″ lift up front with method 17×8.5 on 295/70 17 nittos mt’s. I’m rubbing on the upper control arm at full lock. I’m thinking spidertrax 1.25″ spacers. Thoughts. I have jba control arms.
I had the same issue after JBA UCA. Also gnment fixed it but I’m picking these up to give more clearance. Wish they came in smaller sizes though.
For the SoCal folks out there, The Truck Shop in San Diego (Miramar) CNC their own wheel spaces (as well as UCAs, sliders, bumpers, links, sway bar spacers & other suspension accessories) under the Built Right USA name. Having added a number of their in-house made parts to my rig (@barcelona_trail4r) I would highly recommend these guys for any of your Toyota needs. Ask for James or Ryan. The instagram handles are @thesdtruckshop & @builtrightusa
FYI – my wheel spacers are 1.5″ up front and 1.25″ in the rear. The small difference makes a big difference in an aggressive look
Was wondering if anyone has used the BORA (Bulletproof Off Road Adapters) wheel spacers on their 4R. They have different sizes varying from 0.75″ up to 2.00″.
Just installed last night with correct tourqe
And now getting a clicking noise when tapimg on breaks. Only applying the breaks will it click
I had the same “clicking noise” issue after i got a lift + new tires. After a lot of investigating, the shop realized the BMC was ever so slightly touching a washer so that whenever i hit the brakes, the weight shifting forward would rub and cause the clicking. Simple fix was to hammer the area of the BMC to add a little more clearance. Not 100% sure if you are having the same issues, but wanted to help if I could.
Good afternoon! With the addition of the 1.25″ wheel spacers, is it necessary to change out the wheel studs to give better reach and grip for the lug nuts?
Sounds like the only option is to stick with high-quality spacers from Spidertrax. I’ve read a lot about spacers breaking or falling off on the roads. Have to wonder, if installed properly, is there any real worry about malfunction?
If installed properly, “probably” not. The odds of a Spidertrax spacer failing (if installed properly) would likely be lower than that of a knock-off or third-party unknown supplier. Some of these suppliers are on eBay or Amazon selling the same design – however, the parts are produced in China. As long as that facility has decent quality control – you may be fine but it’s hard telling not knowing when it comes from China. This is one mod you want to spend money on. Don’t skimp – go Spidertrax.
Can you tell me how much offset I could get for new wheels that would be equal to adding the spacers? You mentioned -6 on your rig. The style wheel I’m looking at comes in 0mm or -12mm. I can’t decide what will get me to flush with the wheel well.
Thanks for your great website
Hey John, I run SCS 17 X 8.5 6 X 139.7 4.30″ -10mm. I have bfg ko2 285/70/17 and they are perfectly flush. Looks good. Trimming of bumper & mudflats needed, but no BMC… yet… Absolutely no need for spacers unless ya want them to stick out of the fenders.
Hello my name is Ralph I have a 2012 4WD SR5. I recently added new rims and tires (285/70R17) to my stock suspension. At full flex the inner tire is rubbing the upper control arm. I’d like to add these spacers in order to eliminate this rubbing but after reading all the do’s and don’ts I may be creating more of a problem what do you think ? And thanks a ton for creating this very informative site!
Hi Ralph… first of all, let me say this… the spider traxx spacers are very high quality. I run a 2012 Trail Edition. I didn’t want to get into mods to heavily with a tire upgrade to 285s. So I jumped to 275s. I also had a lift and level kit installed. 1.5” on the rear and 2.5” on the front. I then had the wheel spacers installed. Prior to the wheel spacers I had zero rubbing. After the wheel spacers I had just a little rubbing on the front left interior fender while backing up and cranking to the left. With a slight re mod of pushing the interior fender forward, problem solved.
With that said, you should get a lift and level at minimum; toss on the spacers and then be prepared to make a few slight mods to the interior fender plastics which is super easy. I would suspect this may resolve your issues. The lift and level kit on this site is the one I should have purchased but instead installed a different one. They are inexpensive aside from labour costs to install them which should only be a couple hours.
Thanks a whole lot for responding this is very helpful information ! I’m going to go with a set of the thinnest spacers and see what happens before I try any kind of lift. I carry all kinds of flyfishing gear up top so the easier it is to access the better ! I’ll let you know how it turns out again thanks a lot !
Worked beautifully on my 2012 TE with Stock 17s , BFG 275/70/17, the Daytec lift and level kit 2.5 “ front and 1.5” rear.
I had rubbing on the inside front fender liner in reverse while turning.
5 minute fix. Pulled the two screws on each side, pushed the liner forward, screwed it back in…. bam …. what a sexy set of upgrades. Slick. No hacking and slashing required. 275/70 KO2 did the trick in combo with the daytec lift and level and these spacers. Install shop commented on the quality and tolerances of these spacers. Great recommendations on this site!!
I have an OME 3″ susp lift on my 2016 4Runner. I added spacers but got the death wobble between 40mph to 60mph. It is a shake/wobble in the steering that vibrates the whole car, had to take them off. HOw can I prevent that from happening?
Hi David,
I had the same problem after installing a ToyTec 3” lift on my ‘16 4R. Mine was between 50-60 though. I took my wheels and loosened up the spacers and retorqued them to 85ft lbs. Then I put the wheels back on and made sure the wheels were seated properly and torqued them to 85ft lbs. after I did that, no more issue. Another note…I am not running the differential drop on mine either. If you have it installed, it should only help the problem.
Hi, is it safe to tow with these spacers?
I tow multiple times each week using these.
Thanks Daniel. I just installed these on my runner and was worried I needed to take them off to tow. I will be towing a 4k lbs camping trailer and wanted to make sure.
Thanks again!
So, I was going to get new wheels anyhow after my lift, so if i get a negative offset wheel, there will be no need for spacers? But possibly still the issue of rubbing, which I may also have installing a spacer on the stock wheel.
Hi Brenan,
I have a question about the spacers with the following setup: trd rims with BFG ko2 275/70/17 and a king 3 inch lift. I assume there should be no rubbing but not sure. Thanks in advance.
Hey, just curious if you ever added spacers to your 4r? I have similar setup and was hoping for some insight-
Thanks,
Jess
No I did not, I actually went complely different. I went with Falken 285/70/17 and had rubbing on mud flaps when turning my wheel all the way so if you add spacers you will have rubbing.
Hi I’m new to the 4runner scene. I wanted to know if I installed a day star 2.2/1.5 leveling kit on my 2017 sr5 4runner and I get the spacer above if it will rub or do I have enough clearance? I’m running stock tires and rims
With that leveling kit along with stock tires and wheels, you will be close. You may clear everything with the stock 31″ tires and be just fine. Hard to say exactly what will happen as I have no experience with that exact kit, stock tires, and wheel spacers. I feel like you may have some rubbing in reverse when your wheel is fully turned, but you might clear everything all the way around as well. Hard telling but I think if there is any rubbing with this set-up, it will be minimal and pushing back your fender liners might be all that you need to do. You should write a post on it and let us know what happens.
I am anxious to know the results of spidertrax spacers. Have you guys completed the project?
Dustin,
Yes, check it out here: Installing the wheel spacers. Yeah, they rub more than before for sure.
I currently am running 275/70/R17 BFG KO2’s on a stock 16′ Trail Edition w/out KDSS and have no rub at full flex. Could the Spidertrax spacers cause me to rub by widening my stance? I probably wont do any body modifications or fender liner mods until I lift it and put 33″-34″ tires on it.
Brad,
Adding the wheel spacers to your set-up might cause rubbing. By pushing your wheel out, you will be pushing it closer to the fender, which may require pushing and trimming of your fender liner. Check out that link for more information on trimming the fender liner and exactly what it takes to run bigger tires and possibly adding wheel spacers. It’s really not that difficult to trim your liners or push your liners back. That post helps clear some things up and covers each area we touched in order to run the 34″ tires.
I see that the link to amazon shows sale for one pair. Obviously the sizes are the same front and rear at 1.25 correct?
Vince,
Yeah, you want to buy two sets of them for your 4runner. Two spacers come in one box, so you need to buy two boxes. They will work for front and rear wheels. The mount directly onto your rotor.
Hi my name is Steven I have 2018 4runner Off-road and I want to put Spidertrax wheelspacers 1.25 just only for stance and looks but my question is does it rub when im driving on the streets or minor offroading?
How did this work out for you Steven? We’re these 265?
Steven,
With stock wheels and tires, you will probably have some rubbing. When your wheels are at full lock or even just before full lock (especially in reverse), you will probably touch your fender liners. The wheel and tire will be pushed out further, meaning they will come closer to your fender liner, body mounts as well as the 4Runner’s body. A body mount chop is unlikely here (depends on setup), but a fender liner mod will probably be in your future if you put spacers on your 4R. Fender liner mods are easy. Just unscrew your fender liners, punch a new hole further in, push it back and nut it down. Trimming your body and body mounts are again, unlikely. But, you should always prepare for the worst. Every make and model is a little different. Another thing to consider with the spacers is tire shops and your service center. Some tire shops will not touch wheels and tires with spacers. They will get your truck in, call you and tell you to come pick it up. But, some shops are cool about it, they just might charge you more. Also, some people believe that the spacers will cause more stress on your wheel bearings. There is some merit to this but at what rate and time period will this have a “real” effect. We have spacers on our 4Runner, though.
I just put on spacers i have 3″ toytec lift with diff drop and total chaos uca’s it rubbed a little before the spacers. After the spacers it rubbed alot more. Tires i run are nitto ridge grapplers in 285/70/17
Thanks for leaving that post, I have the same set up and do want more rubbing
Hey John, where did you have your rubbing?