After a very long year without my 2010 5th Gen 4Runner, and with Toyota delaying the 6th Gen for at least another year, I caved and picked up a 2019 TRD Off-Road. As it usually starts, she’s pretty stock at this point. With many mods on the list and a completely new build plan, I’ve set my sights on simple yet practical mods, for now.
With a stock 4Runner comes stock height and stock clearance. While an upgraded suspension is on the soon-to-be-listed items, it’s not at the top of the list. We do a lot of camping, and a stock 4Runner is ungodly capable in its stock form. The rear mud flaps on a stock 4Runner have roughly 11″ of clearance on a flat road. It never hurts to have a bit more clearance on dirt roads, and ARK Splash Guard has the perfect solution.
I originally planned to remove the stock flaps, cut off the excess, and reinstall the wheel well plastic. Then it dawned on me that there’s a 98% chance that someone out there makes a mud flap delete kit. As luck would have it, I stumbled upon ARK Splash Guards.
ARK Splash Guards is a family-owned business based in Arizona. The owner, Jason, a fellow enthusiast of Toyotas, decided that after many wheel-well-thrashing trips on the trails, there had to be a product out there that was both long-lasting and didn’t break the bank. With cheap plastic or expensive powder-coated metal materials that would eventually get scratched, Jason built a prototype out of EPDM plastic, and the rest is history.
Table Of Contents
Installation
Tools Needed
- Flat head screwdriver
- Plastic prying tool
- 10mm socket and socket wrench
ARK provides all the materials you’ll need to install their mud-flap delete kit. They even include replacement 10mm bolts, push clips, installation instructions, and a sticker! You only need three tools to get the kit installed and your 4Runner back on the trails.
From start to finish, this install should take ~10 minutes. On a 1-10 scale (10 being the hardest), this is, without doubt, a 1!
Step 1. Remove OEM Hardware
Each OEM mud-flap is held in place with four (4) 10mm bolts and three (3) push clips.
Pick a side and start removing the 10mm hardware. Inside the wheel well, you’ll find three (3) 10mm bolts that need to be removed. On the outside of the mud-flap, underneath the rear bumper, you’ll find one (1) 10mm bolt that also needs to be removed.
Once the 10mm bolts are removed, remove all three (3) push clips. I like to start by inserting a flat-head screwdriver underneath the center pin that holds the clip in place. Gently pry the pin out roughly 1/4″, or just enough to slide your plastic pry bar underneath.
With a gentle tug, the entire clip and pin should pop out.
If you happen to break a clip during the removal process, don’t fret; ARK includes replacements. In fact, you’ll want to use the replacement push clips provided in the kit. Removing and reinstalling plastic clips in any installation will eventually wear them down.
Once all 10mm bolts and push clips are removed, the OEM mud flap should free itself from the body of your 4Runner. Repeat the process on the other side of the truck.
Step 2. Align & Install ARK Mud-Flap Deletes
That’s it, you’re halfway through one of the easiest mods your 4Runner will ever see!
Clean the area of any debris and start by aligning your mud-flaps to the inside of the wheel well with the ARK logo facing out.
Hand-thread one (1) of the provided 10mm bolts into the very top of the mud-flap delete and into the wheel well. With the mud-flap now loosely secure, start by hand threading in the remaining two (2) 10mm bolts into place.
Be sure to install the bolts loosely until the clips are in place. All bolts will be inserted through the innermost openings, and the clips will be secured to the outermost openings.
Pop in all three (3) push clips into the remaining holes. Align the mud-flap delete to the fender flare line and tighten down the three (3) 10mm bolts.
That’s it; installation complete!
Final Thoughts
This is one of those mods that is not only simple and straightforward to install, but it just makes a lot of sense if clearance is what you’re after. Additionally, it gives the rear end of your 4Runner a much more attractive and low-profile appearance.
ARK’s rear mud-flap deletes are made from 1/8″ EPDM (ethylene propylene diene monomer) plastic, which is the same material often used to coat exterior electrical wires. So, chances are, this stuff will last. Using less techy terms, the rear mud-flap delete material feels similar to a durable (but thinner) plastic cutting board. Mud doesn’t seem to bond to these pieces nearly as much as it did to the OEM flaps.
While the OEM plastic wheel well guards were probably sufficient, they are bulky, and over time, the plastic starts to show its age.
Lastly, ARK offers custom-etched logos on its products. If you’re interested in having something like your Instagram handle or the Trail4R logo etched into the mud flap, please message them directly at sales@arksplashguards.com.
With all of that said, this is one hell of a product and something you should strongly consider if you’re looking for better clearance or that low-profile look!
hows the performance on gravel roads when towing?
thanks
how do you think these compare to the RevTek?
Have you noticed any chips or dings on your rear rocker panels? I mean, the mud flaps definitely serve a purpose (protection), so I wonder if removing them has caused any issues. The deletes look fantastic, just not sure if I do enough “off-roading” to justify losing the extra paint/body protection.
Would you rather have the bumper ripped off when you snag something or some small chips in your paint?
Has anyone come up with a front mud flap delete kit for a 5th gen?
Huh? You just remove them lol. There’s no hole in the front like there is in the rear. What kind of kit would you be wanting?
I was curious about front kits as well. the exposed frame with the Bolt / Clip holes doesn’t look great on the white car. would like to match with the black rear kit
Great job as always bud!