Vinyl Wrapping Your Valance, Grille and Hood on the 5th Gen 4Runner

4runner vinyl front end

Step-By-Step Install On How To Apply Vinyl Wrap To Your 5th Gen 4Runner

I originally got the idea of vinyl wrapping my own 4Runner as a cheaper alternative to buying lower valances to make it look like a TRD. Along with a customized look, there are many other benefits to vinyl wrapping.

  • Custom color selection/design
  • Cost-effective
  • Paint protection
  • Easily removable
  • No permanent damage or alteration to paint

Note: If you have a dent or major body issues, it will show through since the wrap is tight to the body. I have license plate frame holes and you can see them through the vinyl, but it is minimal.

I called a few shops to get quotes to wrap the front lower valence and they were over $200. I did some research and was able to get tools and vinyl off of Amazon for about $100.

Tools & Materials:

Before You Start

Pay attention to weather conditions. Windy conditions could cause dust to blow under the wrap. Cold weather also makes the vinyl more difficult to manipulate.

Wash section prior to wrapping. Soap and water. Then use Mothers clay bar kit to remove all grime and wax so it has a clean surface to adhere to.

Step-By-Step Vinyl Wrapping

I decided to wrap my front lower valence, grill bar, upper grill bar, hood, rear bumper, and door handle cups.

If you can take any of the parts off before wrapping I would highly recommend it. It will give you easy access to wrap the vinyl and it allows you to hide your cut line since you can wrap it around the edges.

Step 1. Knifeless Tape Prep

Step-By-Step Install On How To Apply Vinyl Wrap To Your 5th Gen 4Runner

Use the knifeless tape in the corners that you want your vinyl cut at.

The Knifeless tape makes it so you don’t have to take a razor blade to your paint. Knifeless tape in my opinion is a must-have for any vinyl that doesn’t end on an edge of the body part.

For example, I used the knifeless tape on my hood on the sides of the hump. On the front and back, I cut with a razor blade. Make sure to leave about 4-6” of extra tape on each side of your line where the vinyl will end. This will allow for easy accessibility and cutting.

Here is a good video that shows how to use the knifeless tape.

Step 2. Apply Vinyl

Step-By-Step Install On How To Apply Vinyl Wrap To Your 5th Gen 4Runner

Take your vinyl wrap (with the backing still on), lay it over the area you want to wrap, and then make sure to have extra past your cut lines 2-8”. When in doubt, leave more to avoid it getting too short. The idea is to have the wrap be one single piece. The excess also gives you something to grab onto to pull the wrap around your part.

Remove the backing and place it on the flatter face of the bumper. Use your hand and the squeegee to get it as flat as possible without air bubbles. The great thing about vinyl wrap is if you get a bubble or wrinkle just pull it back to the bubble and start again. If a wrinkle keeps happening, apply some heat to make the vinyl stretch.

Grab a Heat Gun (& a Willing Friend) To Smooth Out Wrinkles

Step-By-Step Install On How To Apply Vinyl Wrap To Your 5th Gen 4Runner

In the tight areas, it really helps to have an extra pair of hands. I had my wife help, she would use the heat gun while I stretched the vinyl and kept applying it.

You can keep working until you are satisfied with the outcome. Try to avoid overheating, the vinyl will overstretch and become too thin. Depending on the color you are using, could cause discoloration in the overstretched areas.

Make sure to finish the wrap past the knifeless tape. When you are happy with the vinyl, take the heat gun and go over the whole piece. If you overstretch it, the heat will cause some pull up.

Step 3. Cut Vinyl

Knifless Tape cut

For the knifeless tape sections, I like to cut a slit into the vinyl wrap to have a starting point for the knifeless tape to cut so it doesn’t drag the wrap. Fold the tape over itself and pull to separate the fishing line from the green tape. Put the fishing line into your slit.

Continue to pull the line through cutting the vinyl wrap; continue on to the end. Use a razor blade on any of the edges to cut the excess vinyl off.

Step 4. Remove Excess Vinyl

Removing Knifeless Tape

Remove the cut vinyl as well as the green tape. The green tape usually splits in two.

One comes with the fishing line and the other is left on the vinyl. Make sure to get it all off.

Step 5. Final Touches

Step-By-Step Install On How To Apply Vinyl Wrap To Your 5th Gen 4Runner

Now that you have the excess vinyl and tape removed, use a heat gun and squeegee the cut edge down to the paint. I went over the entire vinyl one more time with heat to make sure it got a good adhesion. If you have any light scratches from the squeegee apply heat and the majority of the scratches will disappear.

If you see any air bubbles left try using a needle or you can buy a vinyl wrap tool and poke the bubble releasing the air and squeegee it down.

Final Thoughts

I ended up with a few wrinkles on the side of the valence that I couldn’t get out, but they are barely noticeable. I am happy with it,  but after getting more experience of wrapping other parts, I know I could go back and re-do the front valence a lot better.

Once you get the hang of this you can virtually try wrapping everything. Anything that is flat is very easy to do. The curves and turns are where it can be tricky and will take more practice and patience.

Overall I think this is a great, cheap mod to do to your 4Runner. It can set it off and make it unique. There are endless possibilities with vinyl wrap and allows you to be creative.

And like I mentioned before, one of the best things about vinyl wrapping…if you get tired of it, simply pull it off.

Subscribe
Notify of
guest

13 Comments
Inline Feedbacks
View all comments
Penny G
Penny G
6 months ago

All good information. I can’t believe I can’t find anything on how to wrap the limited chrome front bumpers. But thanks see you all give it a shot this weekend probably.

Andrew B.
Andrew B.
6 months ago

Great write up! Wondering if you could share any update and/or photos of how it has handled the last few years? Curious if is small road grit has dinged it up, winter weather/salt, and what about car washes?

allen joseph
allen joseph
1 year ago

Your work is really good and I appreciate this information. I forever prefer to read quality and glad I found this thing in your post. Thank you for the comprehensive article.
for packaging : https://scmpackaging.com/

Mike Bonds
Mike Bonds
2 years ago

This was the exact info I needed! Going to wrap the chrome trim on my 21’ limited

Stephen
Stephen
3 years ago

Looks great! One question would be how did you make it look so clean where the Toyota logo goes and dips down? The rest seems very straightforward.

Jeff - @jeffsteffens2
Jeff - @jeffsteffens2
3 years ago
Reply to  Stephen

I took the grill bar off and removed the logo part(2 screws). Start wrapping from bottom to top. The logo dip part will be last. Use the heat gun and stretch the vinyl. Pull it to get it as smooth as possible near the front of the bar where it will be visible. There were some wrinkles still but when I put the logo back on they were pretty much hidden. Might help to make some small cuts in the vinyl to move it. But try to only cut to where the logo will hide it.
Hope that helps!

Scott - @Salty_4runner
4 years ago

Great article! I used plastidip on my lower valance but I think this might be something to look into in the future!

Ryan Gibbons
Ryan Gibbons
4 years ago

Great article! This got me thinking about wrapping my pro grill vs. Plastidip…

Jeff - @jeffsteffens2
Jeff - @jeffsteffens2
4 years ago
Reply to  Ryan Gibbons

Thanks! My roof rails are plastidipped and I like the vinyl better. To me it has a cleaner look. It would be fairly easy to do with it off. I had some trouble around the Toyota emblem. But I assume you’re talking about the heritage one with the Toyota letters? That one should be a lot easier as it doesn’t have any big turns in it.

Last edited 4 years ago by Jeff Steffens
Lou
Lou
4 years ago

Thank you for this, didn’t know about the knifeless tape. Thats a neat trick!

Last edited 4 years ago by Lou
Jeff - @jeffsteffens2
Jeff - @jeffsteffens2
4 years ago
Reply to  Lou

I stumbled across it and it is the best thing ever for vinyl wrapping!

Mat
Mat
4 years ago

Hey! Cool article! Can you tell me what those red hook points in the front are? Look so good and would love to install those on my car while doing the 2014+ conversion

Jeff - @jeffsteffens2
Jeff - @jeffsteffens2
4 years ago
Reply to  Mat

Thanks! They are shackles that go on your front tow hooks. A note here though, these are not “recovery points” and more or less used for tow points and tie down points. Minor tows or very minor recovery situations may be ok but for severe recoveries, these points are not rated.
https://www.amazon.com/gp/product/B07JVCHQCW/ref=ppx_yo_dt

13
0
Questions or Comments?x
()
x